|
DESCRIPTION : water
base epoxy self level epoxy flooring
is a third generation “water-based”
3 component, epoxy flooring system that outperforms
and outlasts most solvent based and solvent free
flooring systems without the associated odors,
flammability, or VOC’s.
ADVANTAGES
- Waterborne
- Solvent-Free
- Excellent Adhesion
- Applies to Damp Concrete
- Excellent Gloss & Gloss Retention
- Good Color
- Excellent Stain Resistant
- Excellent Hardness Development
- Rapid Dry Time
- Easy Clean-up
- APPLICATION: MIPRO-WBE SL is recommended for...
- Clean room flooring,
- High abrasion resistant flooring
- PACKING : 10 Kgs., 25 Kgs & 50 Kgs Units of
Part A & B
PROPERTIES:
| Property |
Typical
Value
|
|
Shelf Life
|
1
year in sealed container in cool, dry place |
| Mixing
Ratio by wt. |
As
mention on packing |
Coverage
2mm th.
|
3.4-4.5
kg/M2 |
| Application
Method |
Notch
trowel & spike roller |
| Ready
for Foot Traffic |
36-48
hrs.
|
| Ready
for Heavy Traffic |
7
days |
| UV
Light Resistant |
Good |
| Flammability |
Self
extenuating |
| Water
Absorption |
Less
then 1%
|
COVERAGE : This product should be applied at the rate
of approx. 3.5-4.5 kg/M2 for approx. 2mm thick flooring.
SURFACE PREPARATION : The substrate
must be clean, dry and sound with new concrete
cured for at least 28 days. Remove dust, laitance,
grease, curing compounds, waxes, foreign particles,
disintegrated or soft base materials, and any
previously applied coatings. Create a surface
profile on concrete by either steel shot blasting
or acid etching. Repair cracks and joints with
EPOXYE CRACK & PATCH mortar.
If the concrete surface is not prepared properly,
product adhesion will fail and warranties will
be voided.
|
FOR BEST RESULTS
- For interior use only
- New Concrete must cure for 28 days
- DO NOT thin MIPRO-WBE
- DO NOT use when humidity Exceeds 85%
- DO NOT allow material to Puddle during application
- Allow each coat to Dry Tack-Free and clear before
Recoating
- Apply Each Coat Within 24 hours of previous Coat
- Do NOT APPLY to Structurally Unsound Surfaces.
- Apply a Test Patch to Ensure Adhesion to Old
Paint
MIXING: Avoid mixing and application of this product
if the surface temperature is high and humidity is
higher then 70% R.H. The temperature of the surface,
materials and air in the area of installation all
play a role in how the product will apply and cure.
Stair part A & B separately and then pour part
`B in to part A in proper ratio and blend thoroughly
for minimum for 2-3 minutes with a spiral mixing
blade attached to a low-speed electric drill. Take
care not to induce air into the material when mixing.
This will cause bubble in the coating when applied.
POT LIFE : At 30o C and 50% R.H. the MIPRO-WBE has
a useful working time or pot life of 25-30 minutes.
Using any product beyond this time will result in
variable results and therefore any mixed product
beyond the pot life should be discarded.
APPLICATION: The recommended application of this
product is by notch trowel and spike roller. Allow
MIPRO-WBE SL to dry thoroughly before mixing and
applying the next coat. It should be tack free and
clear in appearance before recoating.
CLEAN-UP: Application equipment should be cleaned
using soap and water.
HEALTH & SAFETY It is advisable
to wear protective wears at the time of use of
Water bse epoxy S/L and all other our products.
In case of contact with eyes and skin, wash with
plenty of water and consult a doctor.
This information, given above in good faith, is
based on results gained from experience and tests.
However, all recommendations or suggestions are made
without guarantee since the conditions of use is
beyond our control.
|
